ASTM F formally recognizes the use of in situ probes as a means of conducting relative humidity testing. In fact, ASTM F represents a fundamental. ASTM F ASTM F RH (Relative Humidity). Testing Protocol: ASTM Abstract: Significance and Use. Moisture permeating from concrete floor slabs. Standard Test Method for Determining Relative Humidity in Concrete Floor Using in situ Probes. Apparatus – Humidity Probe and Digital Meter Accuracy ± %.
|Published (Last):||13 January 2011|
|PDF File Size:||16.90 Mb|
|ePub File Size:||15.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
If you forward to 1: Is this acceptable or compromise the test? ASTM F is an excellent test for determining the actual moisture condition of a slab.
This site uses Akismet to reduce spam. UPS peak season may cause delays. The initial ASTM F for in situ RH testing was established inafter continuing research at Scandinavian universities in the s identified the exact specifications for conducting a reliably accurate RH test—placing the test probe at 40 percent depth for slabs poured on grade or 20 percent for slabs drying from both sides.
Updated ASTM F Reflects the Newest Science about RH Testing | Wagner Meters
The standard aetm precise guidelines for RH testing methods. With all areas of ASTM-compliant RH testing, precision is key and data integrity must also be the focus for each flooring professional.
You consent to our cookies if you continue to use our website. These requirements for the standard apply regardless of the RH test method being used. Leave a Reply Cancel reply Your email address will not be published.
Updated ASTM F2170 Reflects the Newest Science about RH Testing
How do you handle this problem? In practice, readings are often taken before the 72 hours has passed, so contractors have an idea of how things are trending.
Other methods typically involve taking measurements only at the surface of the slab. It has been believed that the change in the asstm weight could be translated into a moisture ratio for the concrete beneath.
By testing non-destructively per ASTM F, the inspector can get an instant and precise evaluation of the moisture conditions within 1. Without it, even a well-dried and functioning foundation can end up with concrete slab moisture problems. Finally, for best results, the combination of ASTM F non-destructive moisture content testing and F in-situ relative humidity testing allows for a more complete picture of the moisture conditions of the slab.
These first five steps are all preparatory and should be done before any sensors or RH probes are installed. I would verify that the hole depths are consistent and that environmental conditions are at service conditions.
There is a potential f21700 condensation to appear on the sensor during the test period, due to the high relative humidity within the concrete until the concrete has sufficiently dried.
When To Test Concrete To ASTM F?
June 9, at 1: At this point, satm one test fails, they all fail. Jason, I appreciate this means to contact you. Use our checklist to record and report the RH readings. Each hole must have a liner that isolates the sensor from ambient conditions, and sensors must have NIST-traceable calibration. Note that the liner requirements have been updated and the hole is to be fully lined to meet the ASTM standard.
Surface-based test results will fluctuate, even more, under these changes in environmental conditions. First, I have to state that F is specified for interior applications that are under consistent ambient air controls. As far back as the s, laboratories at the Portland Cement Association conducted controlled tests that verified the accuracy of RH testing.
When To Test Concrete To ASTM F2170?
For flooring and concrete professionals, ASTM F provides the asrm for using relative humidity RH testing when measuring moisture content in concrete slabs. Leave a Reply Cancel reply Your email address will not be published.
In celebration of the New Year, we will be closing early at In part, the idea was to assess if it is actually necessary to wait the full 72 hours for an accurate, astj moisture readings.
RH Testing and Reporting Drill and prepare the test holes. Sub-grade water vapor can permeate even well-mixed and applied slabs.
This can only be done with reusable relative humidity probes that can be removed after one hour and reinserted at any time in the future to ensure accurate results. Meeting this standard provides the groundwork for limiting moisture-related flooring problems and the many liabilities and mitigation problems that can result from excess moisture.
While any professional must understand the exact requirements of standard F the most recent versionthe following are 10 guidelines to help ensure that you have met the criteria laid out in ASTM F Section 9 of the standard requires that both the slab and the ambient air above it must be at service conditions for a minimum of 48 hours before testing.
We have people who use the Rapid RH on shallow pours.